Document 800-00031 – Rev A – 04/08Day/NightUltra Wide DynamicFixed Dome CameraUser GuideNTSC / PALHD4U HD4UX
10Connecting Cables Through the Side Conduit 1. Peel back the bottom flat gasket below the side conduit just enough to expose the security screw.2. Us
Document 800-00031 Rev A 1104/08Electrical Box InstallationsFigure 3 illustrates how to mount the HD4U/X directly to a 4S electrical box or directly t
12Figure 4 illustrates how to mount the HD4U/X directly to a double gang or single gang electrical box.Figure 4 Double Gang/Single Gang Electrical Box
Document 800-00031 Rev A 1304/08Connecting the WiringFollow Figure 5 to connect the video and power wires.Figure 5 Wiring ConnectionAdjusting the Came
14Figure 6 Gimbal AdjustmentAdjusting the Lens FocusLenses are pre-focused at the factory but may require a final adjustment after installation becaus
Document 800-00031 Rev A 1504/08Camera SetupCamera FunctionsOSD Menu Structure- Press down on the joystick and hold two seconds to access the MAIN MEN
16Configuring the WDR PresetsSelect the appropriate camera mode for the lighting conditions.<CUSTOM> Opens the CUSTOM screen where you can adjus
Document 800-00031 Rev A 1704/08Optimizing the Camera SetupNote This menu is for advanced users only.The table below explains the options on the CAMER
18>SYNC Synchronize the vertical interval sync pulse of your camera with other equipment to reduce the effect of picture roll on the monitor. Selec
Document 800-00031 Rev A 1904/08Setting the Camera Image PropertiesThe table below explains the options on the VIEWING menu.<ATW Xtnd> Automati
2RevisionsIssue Date RevisionsA 04/08 New document.
20>FLIP Select either:<ON> to reverse the image horizontally on the video monitor, or<OFF> (default)> ID DISPLAY. Select ON to open
Document 800-00031 Rev A 2104/08Setting the Day/Night ControlThe table below explains the options on the DAY/NIGHT SETUP menu.NoteThis setting is depe
22Restoring SettingsOn the main MENU, select RESTORE DEFAULTS, then YES followed by ENTER (middle button). This reloads the factory default camera set
Document 800-00031 Rev A 2304/08Installing the Enclosure CoverTo install the enclosure cover, use the Allen key (supplied) to secure the HD4U/X dome e
24Solving Common Technical IssuesNo Video❐❐❐Check that the power supply voltage is within the operating specifications for your camera model. See Spec
Document 800-00031 Rev A 2504/08Warranty and ServiceSubject to the terms and conditions listed on the Product warranty, during the warranty period Hon
26SpecificationsVideo Signal SpecificationsNTSC PALVideo Standard: 525 lines, 2:1 interface 625 lines, 2:1 interfaceScanning System: ProgressiveImage
Document 800-00031 Rev A 2704/08Temperature: Operating: -13°F to +122°F (-25°C to +50°C)Storage: -4°F to +140°F (-20°C to +60°C)Mechanical Specificati
28Cable GuidelinesMaximum Power Supply Cable Length (feet/meters)Cameras With AC/DC Power SuppliesWire gaugeTotal loadPower supply24 AWG 22 AWG 18 AWG
Document 800-00031 Rev A 2904/08HD4U Mounting Template
Document 800-00031 Rev A 304/08WarningsInstallation and servicing should be performed only by qualified and experienced technicians to conform to all
30
Document 800-00031 Rev A 3104/08
© 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Ho
4FCC Compliance StatementInformation to the User: This equipment has been tested and found to comply with the limits for a Class B digital device. Pur
Document 800-00031 Rev A 504/08ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6IntroductionThe unobtrusive, low-profile design of the HD4U/X CCTV Camera is ideal for indoor and outdoor installations in commercial and residential
Document 800-00031 Rev A 704/08Equipment RequiredYou will require the following tools to complete the installation:• Phillips screwdriver• Tools suppl
8InstallationThe HD4U/X is weather-sealed for indoor or outdoor locations. The HD4U/X is a fully-integrated enclosure with camera and lens. The wiring
Document 800-00031 Rev A 904/08Connecting Cables Through the Housing BaseFor installations that require pulling cables through the grommet located in
Commenti su questo manuale